? semiconductor components industries, llc, 2005 november, 2005 ? rev. 6 1 publication order number: MC10EL57/d MC10EL57, mc100el57 5vecl 4:1 differential multiplexer description the mc10/100el57 is a fully differential 4:1 multiplexer. by leaving the sel1 line open (pulled low via the input pulldown resistors) the device can also be used as a differential 2:1 multiplexer with sel0 input selecting between d0 and d1. the sel1 is the most significant select line. the binary number applied to the select inputs will select the same numbered data input (i.e., 00 selects d0). multiple v bb outputs are provided for single-ended or ac coupled interfaces. the v bb pin, an internally generated voltage supply, is available to this device only. for single-ended input conditions, the unused dif ferential input is connected to v bb as a switching reference voltage. v bb may also rebias ac coupled inputs. when used, decouple v bb and v cc via a 0.01 f capacitor and limit current sourcing or sinking to 0.5 ma. when not used, v bb should be left open. the 100 series contains temperature compensation. features ? useful as either 4:1 or 2:1 multiplexer ? v bb output for single-ended operation ? pecl mode operating range: v cc = 4.2 v to 5.7 v with v ee = 0 v ? necl mode operating range: v cc = 0 v with v ee = ? 4.2 v to ? 5.7 v ? internal input pulldown resistors on all inputs ? q outputs will default low with inputs open or at v ee ? pb ? free packages are available* *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. so ? 16 d suffix case 751b 1 16 marking diagrams* 1 16 10el57g awlyww a = assembly location wl = wafer lot yy = year ww = work week g= pb ? free package 1 16 100el57g awlyww *for additional marking information, refer to application note and8002/d. http://onsemi.com see detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. ordering information
MC10EL57, mc100el57 http://onsemi.com 2 table 1. attributes characteristics value internal input pulldown resistor 75 k internal input pullup resistor n/a esd protection human body model machine model charge device model > 1 kv > 100 v > 2 kv moisture sensitivity (note 1) level 1 flammability rating oxygen index: 28 to 34 ul 94 v ? 0 @ 0.125 in transistor count 109 devices meets or exceeds jedec spec eia/jesd78 ic latchup test 1. for additional moisture sensitivity information, refer to application note and8003/d. d1 figure 1. logic diagram and pinout assignment d0 d2 d2 d3 15 16 14 13 12 11 10 2 1 3456 7 v cc 9 8 d3 d0 sel0 sel1 qq v bb1 v bb2 v ee d1 4:1 data out d0 d1 d2 d3 d0 ? 3, d0 ? 3 ecl diff data inputs sel0,1 ecl mux select inputs q, q ecl data outputs v bb1 , v bb2 reference voltage output v cc positive supply v ee negative supply table 2. pin description sel1* l l h h sel0* l h l h table 3. function table pin function * pin will default low when left open.
MC10EL57, mc100el57 http://onsemi.com 3 table 4. maximum ratings symbol parameter condition 1 condition 2 rating unit v cc pecl mode power supply v ee = 0 v 8 v v ee necl mode power supply v cc = 0 v ? 8 v v i pecl mode input voltage necl mode input voltage v ee = 0 v v cc = 0 v v i v cc v i v ee 6 ? 6 v v i out output current continuous surge 50 100 ma ma i bb v bb sink/source 0.5 ma t a operating temperature range ? 40 to +85 c t stg storage temperature range ? 65 to +150 c ja thermal resistance (junction ? to ? ambient) 0 lfpm 500 lfpm soic ? 16 soic ? 16 130 75 c/w c/w jc thermal resistance (junction ? to ? case) standard board soic ? 16 33 to 36 c/w t sol wave solder pb pb ? free <2 to 3 sec @ 248 c <2 to 3 sec @ 260 c 265 265 c maximum ratings are those values beyond which device damage can occur. maximum ratings applied to the device are individual str ess limit values (not normal operating conditions) and are not valid simultaneously. if these limits are exceeded, device functional operation i s not implied, damage may occur and reliability may be affected. table 5. 10el series pecl dc characteristics v cc = 5.0 v; v ee = 0 v (note 1) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 24 24 24 ma v oh output high voltage (note 5) 3920 4010 4110 4020 4105 4190 4090 4185 4280 mv v ol output low voltage (note 2) 3050 3200 3350 3050 3210 3370 3050 3227 3405 mv v ih input high voltage (single ? ended) 3770 4110 3870 4190 3940 4280 mv v il input low voltage (single ? ended) 3050 3500 3050 3520 3050 3555 mv v bb output voltage reference 3.57 3.7 3.65 3.75 3.69 3.81 v v ihcmr input high voltage common mode range (differential configuration) (note 3) 2.5 4.6 2.5 4.6 2.5 4.6 v i ih input high current 150 150 150 a i il input low current 0.5 0.5 0.3 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. input and output parameters vary 1:1 with v cc . v ee can vary +0.06 v / ? 0.5 v. 2. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 3. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v.
MC10EL57, mc100el57 http://onsemi.com 4 table 6. 10el series necl dc characteristics v cc = 0 v; v ee = ? 5.0 v (note 4) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 24 24 24 ma v oh output high voltage (note 5) ? 1080 ? 990 ? 890 ? 980 ? 895 ? 810 ? 910 ? 815 ? 720 mv v ol output low voltage (note 5) ? 1950 ? 1800 ? 1650 ? 1950 ? 1790 ? 1630 ? 1950 ? 1773 ? 1595 mv v ih input high voltage (single ? ended) ? 1230 ? 890 ? 1130 ? 810 ? 1060 ? 720 mv v il input low voltage (single ? ended) ? 1950 ? 1500 ? 1950 ? 1480 ? 1950 ? 1445 mv v bb output voltage reference ? 1.43 ? 1.30 ? 1.35 ? 1.25 ? 1.31 ? 1.19 v v ihcmr input high voltage common mode range (differential configuration) (note 6) ? 2.5 ? 0.4 ? 2.5 ? 0.4 ? 2.5 ? 0.4 v i ih input high current 150 150 150 a i il input low current 0.5 0.5 0.3 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. input and output parameters vary 1:1 with v cc . v ee can vary +0.06 v / ? 0.5 v. 5. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 6. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v. table 7. 100el series pecl dc characteristics v cc = 5.0 v; v ee = 0 v (note 7) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 24 24 27 ma v oh output high voltage (note 8) 3915 3995 4120 3975 4045 4120 3975 4050 4120 mv v ol output low voltage (note 8) 3170 3305 3445 3190 3295 3380 3190 3295 3380 mv v ih input high voltage (single ? ended) 3835 4120 3835 4120 3835 4120 mv v il input low voltage (single ? ended) 3190 3525 3190 3525 3190 3525 mv v bb output voltage reference 3.62 3.74 3.62 3.74 3.62 3.74 v v ihcmr input high voltage common mode range (differential configuration) (note 9) 2.5 4.6 2.5 4.6 2.5 4.6 v i ih input high current 150 150 150 a i il input low current 0.5 0.5 0.5 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 7. input and output parameters vary 1:1 with v cc . v ee can vary +0.8 v / ? 0.5 v. 8. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 9. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v.
MC10EL57, mc100el57 http://onsemi.com 5 table 8. 100el series necl dc characteristics v cc = 0 v; v ee = ? 5.0 v (note 10) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 24 24 27 ma v oh output high voltage (note 11) ? 1085 ? 1005 ? 880 ? 1025 ? 955 ? 880 ? 1025 ? 955 ? 880 mv v ol output low voltage (note 11) ? 1830 ? 1695 ? 1555 ? 1810 ? 1705 ? 1620 ? 1810 ? 1705 ? 1620 mv v ih input high voltage (single ? ended) ? 1165 ? 880 ? 1165 ? 880 ? 1165 ? 880 mv v il input low voltage (single ? ended) ? 1810 ? 1475 ? 1810 ? 1475 ? 1810 ? 1475 mv v bb output voltage reference ? 1.38 ? 1.26 ? 1.38 ? 1.26 ? 1.38 ? 1.26 v v ihcmr input high voltage common mode range (differential configuration) (note 12) ? 2.5 ? 0.4 ? 2.5 ? 0.4 ? 2.5 ? 0.4 v i ih input high current 150 150 150 a i il input low current 0.5 0.5 0.5 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 10. input and output parameters vary 1:1 with v cc . v ee can vary +0.8 v / ? 0.5 v. 11. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 12. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v. table 9. ac characteristics v cc = 5.0 v; v ee = 0 v or v cc = 0 v; v ee = ? 5.0 v (note 13) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit f max maximum toggle frequency tbd tbd tbd ghz t plh t phl propagation data q/q delay sel q/q 350 440 550 690 360 440 560 690 380 460 580 710 ps t skew input skew d n , d m to q 100 100 100 ps t jitter cycle ? to ? cycle jitter tbd tbd tbd ps v pp input swing (note 14) 150 1000 150 1000 150 1000 mv t r t f output rise/fall times q (20% ? 80%) 125 375 125 375 125 375 ps note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 13. 10 series: v ee can vary +0.06 v / ? 0.5 v. 100 series: v ee can vary +0.8 v / ? 0.5 v. 14. v pp min is minimum input swing for which ac parameters guaranteed. the device has a dc gain of 40.
MC10EL57, mc100el57 http://onsemi.com 6 figure 2. typical termination for output driver and device evaluation (see application note and8020/d ? termination of ecl logic devices.) driver device receiver device qd q d z o = 50 z o = 50 50 50 v tt v tt = v cc ? 3.0 v ordering information device package shipping ? MC10EL57d soic ? 16 48 units / rail MC10EL57dg soic ? 16 (pb ? free) 48 units / rail MC10EL57dr2 soic ? 16 2500 / tape & reel MC10EL57dr2g soic ? 16 (pb ? free) 2500 / tape & reel mc100el57d soic ? 16 48 units / rail mc100el57dg soic ? 16 (pb ? free) 48 units / rail mc100el57dr2 soic ? 16 2500 / tape & reel mc100el57dr2g soic ? 16 (pb ? free) 2500 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. resource reference of application notes an1405/d ? ecl clock distribution techniques an1406/d ? designing with pecl (ecl at +5.0 v) an1503/d ? eclinps i/o spice modeling kit an1504/d ? metastability and the eclinps family an1568/d ? interfacing between lvds and ecl an1642/d ? the ecl translator guide and8001/d ? odd number counters design and8002/d ? marking and date codes and8020/d ? termination of ecl logic devices and8066/d ? interfacing with eclinps and8090/d ? ac characteristics of ecl devices
MC10EL57, mc100el57 http://onsemi.com 7 package dimensions 0.25 (0.010) t b a m s s min min max max millimeters inches dim a b c d f g j k m p r 9.80 3.80 1.35 0.35 0.40 0.19 0.10 0 5.80 0.25 10.00 4.00 1.75 0.49 1.25 0.25 0.25 7 6.20 0.50 0.386 0.150 0.054 0.014 0.016 0.008 0.004 0 0.229 0.010 0.393 0.157 0.068 0.019 0.049 0.009 0.009 7 0.244 0.019 1.27 bsc 0.050 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 1 8 9 16 ? a ? ? b ? d 16pl k c g ? t ? seating plane r x 45 m j f p 8 pl 0.25 (0.010) b m m so ? 16 d suffix case 751b ? 05 issue j on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada japan : on semiconductor, japan customer focus center 2 ? 9 ? 1 kamimeguro, meguro ? ku, tokyo, japan 153 ? 0051 phone : 81 ? 3 ? 5773 ? 3850 MC10EL57/d eclinps is a trademark of semiconductor components industries, llc (scillc). literature fulfillment : literature distribution center for on semiconductor p.o. box 61312, phoenix, arizona 85082 ? 1312 usa phone : 480 ? 829 ? 7710 or 800 ? 344 ? 3860 toll free usa/canada fax : 480 ? 829 ? 7709 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : http://onsemi.com order literature : http://www.onsemi.com/litorder for additional information, please contact your local sales representative.
|
